Yamaha EMX512SC Powered Mixer 2 x 500w

Experienced musicians, performers, speakers, and club operators know the importance of a high-quality sound system with the right features and performance to deliver their sound. Where portability and convenience are important criteria, a system based on a high-performance Yamaha EMX-series powered mixer is definitely the way to go. In one integrated, portable unit you have a mixer to combine and balance your microphone and instrument and line sources, effects to refine and polish your sound, and power to drive the main speakers and even monitor speakers as well. But that's nowhere near the whole story - Yamaha EMX-series Powered Mixers offer a range of features that let you mix, process, and deliver your sound with maximum quality and creative control … and, of course, that unrivalled Yamaha sound.

• Maximum Output Power @ 0.5 % THD at 1 kHz 500 W/4 Ω; 350 W/8 Ω
• Frequency Response -3, 0, 1 dB 20 Hz-20 kHz, ref to the nominal output level @ 1 kHz
• Total Harmonic Distortion Less than 0.5 % (THD+N) +14 dB @ 20 Hz, 1 kHz, 20 kHz, GAIN control: all nominal
• Hum & Noise Equivalent Input Noise, -115 dBu, Rs = 150 Ω CH 1-4 MIC/LINE: MIC
• Crosstalk -65 dB @ 1 kHz
• Input Connectors CH 1-4: XLR and Phone; CH 5/6, 7/8: XLR and Phone; CH 9/10, 11/12: XLR and Pin
• CH EQ HIGH, MID, LOW
• Phantom Power 15 V
• Graphic Equalizer 7 Band (125, 250, 500, 1 k, 2 k, 4 k, 8 kHz): Main (Stereo) and Monitor
• Digital Effects SPX Digital Multi Effector (24 bit AD/DA, 32 bit Internal Processing): 16 Programs
• Power Amp Mode Main L/R, Main (L+R)/Monitor
• Foot Switch On/Off
• Dimensions (W x D x H) 442 x 274 x 286 mm (17-3/8" x 10-3/4" x 11-1/4")
• Weight 10 kg (22 lbs.)
• Power Requirements 120 V 60 Hz
• Power Consumption 450 W
• INPUT CHARACTERISTICS
• Input Terminals MIC/LINE Actual Load Impedance For Use With Nominal Input level
• Sensitivity *2 Position Max. before clip
• CH INPUT 1-4 XLR
• *3 MIC 2 kΩ 50-600 Ω Mics -60 dBu
• (0.69 mV) -35 dBu
• (13.8 mV) -15 dBu
• (138 mV)
• LINE -30 dBu
• (21.8 mV) -5 dBu
• (436 mV) +15 dBu
• (4.36 V)
• Phone
• *4 MIC 6 KΩ 600 Ω -50 dBu
• (2.18 mV) -25 dBu
• (43.6 mV) -5 dBu
• (436 mV)
• LINE -20 dBu
• (69.0 mV) +5 dBu
• (1.38 V) +25 dBu
• (13.8 V)
• CH INPUT 5/6, 7/8 XLR
• *3 - 2 kΩ 50-600 Ω Mics -60 dBu
• (0.69 mV) -35 dBu
• (13.8 mV) -15 dBu
• (138 mV)
• Phone
• *5 - 10 KΩ 600 Ω Lines -20 dBu
• (69.0 mV) +5 dBu
• (1.38 V) +25 dBu
• (13.8 V)
• CH INPUT 9/10, 11/12 XLR
• *3 - 2 kΩ 50-600 Ω Mics -60 dBu
• (0.69 mV) -35 dBu
• (13.8 mV) -15 dBu
• (138 mV)
• RCA
• Pin - 10 KΩ 600 Ω Lines -20 dBu
• (69.0 mV) +5 dBu
• (1.38 V) +25 dBu
• (13.8 V)
• *1 0 dBu is referenced to 0.775 Vrms.
• *2 Sensitivity is the lowest level that will produce an output of +4 dB (1.23 V), or the nominal output level when the unit is set to maximum level. (All level controls are at
• maximum position.)
• *3 XLR-3-31 type connectors are balanced. (1=GND, 2=HOT, 3=COLD)
• *4 Phone Jacks are balanced. (Tip=HOT, Ring=COLD, Sleeve=GND)
• *5 Phone Jacks are unbalanced.
•  
• OUTPUT CHARACTERISTICS
• Output Terminals Actual Source Impedance For Use With Nominal Output level Connector
• Nominal Max. before clip
• SPEAKER OUT 0.1 Ω 4 Ω Speakers EMX512SC 125 W 500 W [A1, B1] SPEAKON
• [A1, A2, B1, B2] EMX312SC 75 W 300 W [A2, B2] Phone Jack *2
• EMX212S 50 W 200 W
• MAIN OUT [L, R] 600 Ω 10 kΩ Lines - +4 dBu (1.23 V) +20 dBu (7.75 V) Phone Jack *2
• EFFECT OUT 600 Ω 10 kΩ Lines - +4 dBu (1.23 V) +20 dBu (7.75 V) Phone Jack *2
• MONITOR OUT 600 Ω 10 kΩ Lines - +4 dBu (1.23 V) +20 dBu (7.75 V) Phone Jack *2
• REC OUT [L, R] 600 Ω 10 kΩ Lines - -10 dBV (316 mV) +10 dBV (3.16 V) RCA Pin Jack
• *1 0 dBu is referenced to 0.775 Vrms. 0 dBV is referenced to 1 Vrms.
• *2 Phone Jacks are unbalanced.